toyouiop.blogg.se

1. Chris king tool instructions pdf pdf#
2. Chris king tool instructions pdf manual#
3. Chris king tool instructions pdf professional#
4. Chris king tool instructions pdf download#

Chris King’s ThreadFitTM T47 30x/30i BBs are designed to work directly with 30mm spindled crank systems. Chris King’s ThreadFitTM T47 24x/24i BBs are designed to work directly with 24mm and 24/22mm spindled crank systems. Proper spacer configuration is essential for correct bearing preload, chain line and crank arm positioning. Crank Installation Follow crank arm manufacturer’s instructions to determine spacer orientation. The Chris King External BB Cup Tool features an optimized spline interface that minimizes the chance of marring BB cup anodization and is compatible with 3/8” socket wrenches and torque wrenches. BB cups are compatible with the following external BB cup spline tools: ThreadFitTM T47 cups require use of Chris King 30mm BB Cup Tool ThreadFitTM 30/T47x (TBB006), or Chris King BB Cup Tool ThreadFitTM T47i (TBB007). The Non-Drive cup threads into the bottom bracket shell clockwise and the Drive cup threads into the bottom bracket shell counter-clockwise. With proper BB spacers installed on BB cups, thread BB cups into frame using a compatible BB cup spline tool (see below) and torque to 50 Nm (36.88 ft/lbs).

Chris king tool instructions pdf manual#

Please refer to your Chris King ThreadFitTM T47 converison kit manual and you crank manufacturers manual for specific set up information. Your Conversion Kit will include the correct BB cup spacers for proper frame setup. Make sure that the center sleeve is pressed into the Non-Drive BB cup, seating the sleeve on the inner edge of the BB cup (it is recommended with ThreadFitTM T47 cups to apply a thin layer of waterproof grease or Tri-FlowTM to the O-ring inside the cup prior to installation). Apply a generous coating of anti-seize (use Zinc or Copper based anti-seize when installing onto a titanium frame) to the threads on the BB cups, as well as on the BB shell threads on the bicycle frame. Note BB cup orientation marking on outside of cup, Drive and Non-Drive. Clean BB shell threads and surfaces to remove any chips, shavings, grit, and/or cutting oil. Using a small file, deburring tool or sand paper, carefully remove any sharp edges or burrs from the BB shell edges. Be sure to remove all frame paint from BB shell/BB cup interface. Face the BB shell to ensure that the ends are square and parallel to each other. Chase the BB shell threads to ensure that threads are properly formed. Preparation of Bottom Bracket Shell Proper preparation of the BB shell is required for best BB performance, durability, longevity and reduces the possibility of installation problems. ThreadFitTM T47 cups require either the use of Chris King 30mm BB Cup Tool ThreadFitTM 30/T47x (TBB006), or Chris King BB Cup Tool ThreadFitTM T47i (TBB007). FOR CARBON FIBER FRAMES PLEASE CHECK WITH MANUFACTURER REGARDING FRAME PREPARATION. To ensure proper installation, when applicable, the use of high quality facing and thread tapping tools are strongly recommended.

Chris king tool instructions pdf professional#

We recommend that a qualified professional bicycle mechanic perform the procedure. BB installation requires specialized tools. ThreadFitTM T47 Bottom Bracket Installation Before beginning your BB installation please be sure that you have the correct Conversion Kit for your frame and crank system. If your bottom bracket shell width or crankset type is not listed on the table or you have questions about the best possible fit for your bike please be sure to contact your nearest Chris King dealer or reach out to us directly at or by phone at 80. Please see the attached table to help you determine which conversion kit you need. ThreadFitTM T47 24x and 30x require the use of our conversion kits for correct crank installation. Important Notice - Converison Kits Chris King ThreadFitTM T47 bottom brackets are designed specifically to interface with our Chris King bottom bracket conversion kits to give our bottom brackets a wide range of crank system compatibility. With proper installation and maintenance, you can expect to enjoy many years of exception performance from the legendary quality that is built into each and every component we make.

Chris king tool instructions pdf pdf#

PDF Content Summary: ThreadFitTM T47 Bottom Brackets Congratulations! Since 1976, Chris King has been supplying cyclists with the best made, most reliable components in the market.

Chris king tool instructions pdf download#

CLICK HERE TO DOWNLOAD CHRIS KING THREADFIT T47 (01) PDF MANUAL